Мовер XTS Beckhoff AT8300-1100-0100
Вся продукция Beckhoff
Мовер XTS Beckhoff AT8300-1100-0100. Мовер XTS Beckhoff для систем управления движением и приводной техники. Основные технические характеристики, параметры подключения и эксплуатации приведены ниже.
ХАРАКТЕРИСТИКИ
| Артикул: | AT8300-1100-0100 |
| Бренд: | Beckhoff |
| Технические характеристики | |
| Rated power | up to 35 W (depending on the mover position) |
| Peak performance | up to 75 W (depending on the mover position) |
| Выходное напряжение | 24 В DC (regulated) |
| Power transmission | continuously (also across module limits) |
| Communication cycle | 250 µs |
| Communication direction | bidirectional |
| Time response | µs-precise DC synchronization |
| Communication participants | no system limits (individual address assignment of the movers possible) |
| Communication types | cyclic and acyclic |
| Data transfer | continuously (also across module limits) |
| Number of digital inputs | 2 (+2 analog inputs usable as digital input) |
| Технология подключения | 1-wire | Cage Clamp® |
| Номинальное напряжение | 24 В DC (-15%/+20%) |
| Уровень сигнала «0» | -3…+5 V |
| Уровень сигнала «1» | 11…30 V |
| Входной фильтр | configurable, standard: 3 мс, min.: 10 µs |
| Counter | 1 x up/down counter, 1 x up or down counter |
| Counter depth | 32 bit |
| Counter feature | set counter, switch outputs, reset counter |
| Latch function | latch input, 24 В DC |
| Latch resolution | 4 µs resolution, 32 bit time value |
| Number of digital outputs | 4 (+3 PWM outputs usable as digital output) |
| Тип нагрузки | ohmic, inductive, lamp load |
| Switching times | тип. TON: 20 µs, TOFF: 10 µs |
| Short-circuit current | тип. < 2 A |
| Switching-off energy | < 150 mJ/channel |
| Number of analog inputs | 2 |
| Technology | single-ended |
| Signal voltage | 0…10 V |
| Internal resistance | 500 kΩ |
| Input filter cut-off frequency | 2 kHz |
| Разрешение | 12 bit |
| Measurement error/uncertainty | < ±0.3% (relative to full scale value) |
| Количество выходов | 3 x half bridge with 2 x current measurement or 1 x full and 1 x half bridge with 1 x current measurement each |
| Max. output current | 2 A |
| Max. switching frequency | 128 kHz |
| Duty cycle | 0…100% (TON > 20 ns, TOFF > 200 ns) |
| Protection rating | IP20 |
| Сечение подключаемого провода | solid wire: 0.08…1.5 mm², stranded wire*: 0.08…1.5 mm², with ferrule: 0.25…1 mm² |
| Сечение провода AWG | solid wire: AWG28-16, stranded wire*: AWG28-16, with ferrule: AWG28-18 |
| Длина зачистки | 6…7 мм |
| Width | 62 мм |
| Length | 151.3 мм |
| Высота | 28.5 мм |
| Масса | 220 г (housing incl. electronics) | 651 г |
| Rated air gap | 1 мм |
| Особенности | integrated adjustment option for air gap |
| Mover length | 70 мм |
| Rollers material | plastic |
| Magnet pitch | 72 мм |
| Main body material | aluminum |
| Continuous force | AT9001-x550 (5-pin): 30 N (specification refers to straight sections) |
| Peak force | AT9001-x550 (5-pin): 100 N (specification refer to straight sections) |
| Electronical detection | standard |
| Possible curve segments | straight (AT9000, AT9100), 180° (clothoid, AT9050-0500-0170), 45° (AT9040-0750-0070, AT9040-1250-0070) |
| Цифровой вход | Number of digital inputs |
| 2 (+2 analog inputs usable as digital input) | Connection technology |
| 1-wire | Nominal voltage |
| 24 V DC (-15%/+20%) | Signal voltage “0” |
| -3…+5 V | Signal voltage “1” |
| 11…30 V | Input filter |
| configurable, standard: 3 ms, min.: 10 µs | Counter |
| 1 x up/down counter, 1 x up or down counter | Counter depth |
| 32 bit | Counter feature |
| set counter, switch outputs, reset counter | Latch function |
| latch input, 24 V DC | Latch resolution |
| Информация для заказа | |
| AT9001-X550 | (5-pin): 30 N (specification refers to straight sections) | (5-pin): 100 N (specification refer to straight sections) |
